Floor

Apply floor finish

After stripping: several thin coats for a floor that shines and lasts for months.

Level: intermediateAfter strippingNormal traffic the next day
Sealer or finishEquipmentStepsMistakesProducts
Before you start: the floor must be stripped, well rinsed and completely dry. Read the finish label: the number of coats and drying times in this guide are guidelines. The product label always comes first.

1Sealer or finish: the difference

The sealer

It fills the pores of the floor and acts as a base. It is used on a new, porous or very worn floor.

The finish

Often called “wax”. It is the coat that shines and takes the wear. Some products do both.

2The equipment

WhatWhy
A clean finish mop, used only for finishNever a mop that has touched stripper or soap.
A bucket lined with a clean plastic bagThe finish stays clean and the bucket is cleaned in two seconds.
“Wet floor” signsNo one should walk on a fresh coat.
High-speed burnisher and burnishing pad (later)To make the finish shine once it has hardened, if the product allows it.

3The steps

  1. Check the floor

    Just stripped? Follow the stripping guide first. Dry, clean, dust-free. Run a dry mop just before: a hair or a grain of sand stays trapped in the finish for months.

  2. Pour without shaking

    Do not shake the container: it creates bubbles that stay on the floor. Pour gently into the lined bucket.

  3. The sealer, if needed

    One or two thin coats, according to the label.

  4. First coat of finish

    Start at the back of the room and work back toward the door. First do the edge, about 15 cm (6 in) from the wall, then fill in with a figure-“8” motion, in a thin coat. A thick coat dries poorly and stays soft.

  5. Wait between coats

    Each coat must be completely dry before the next one: nothing sticks under your finger. With POLYPLUS 25: about 45 to 55 minutes

    Longer if it is hot or humid, or if the coat is thick.

  6. The next coats

    In total, 2 or 3 coats depending on how porous the floor is.

    For the middle coats, stop 15 cm (6 in) from the wall: otherwise the finish builds up and yellows along the baseboards. Only the first and last coats go all the way to the wall.

  7. Let it harden

    Light traffic after a few hours, normal traffic the next day. Wait before putting heavy furniture back.

  8. Restore the shine, later

    When the floor shines less: clean it, then spray POLYPLUS 25 diluted 50:50 with water and buff (spray-buff method).

How much product? About 1,500 to 2,000 sq. ft. per coat for 4 litres, depending on the floor. A porous floor, or one that has not been sealed in a long time, takes more, especially on the first coat. Example: a 500 sq. ft. room, 3 coats, takes about 4 litres.

4The costly mistakes

To make it last: every day, a dry mop and a neutral cleaner, such as DMT Brille at 1 to 200. From time to time, restore the shine (step 8). This pushes the next stripping back by several months.

5What you need from DMT

PhotoProductCodeSafety data sheet
POLYPLUS 25, Unica, floor finish, 4 LPOLYPLUS 25, Unica, floor finish, 4 L502002-1Coming soon
POLYPLUS 25, Unica, floor finish, 20 LPOLYPLUS 25, Unica, floor finish, 20 L502002-20Coming soon
SEALPLUS, acrylic floor sealer, 4 LSEALPLUS, acrylic floor sealer, 4 L502020-4Coming soon
TRACK-95, gloss restorer, 4 L (maintenance)502029-1Coming soon
Finish mop, 20 oz headFinish mop, 20 oz head900011—
Fibreglass mop handle, 60 in.Fibreglass mop handle, 60 in.900035-C60—
7580J bucket and wringer, 33.1 L7580J bucket and wringer, 33.1 L907580-J—
“Wet floor” sign“Wet floor” sign906111—
Rubbermaid extension handle, 48 to 72 in.Rubbermaid extension handle, 48 to 72 in.900081-755—
Rubbermaid 18 in. frameRubbermaid 18 in. frame900081-560—
Rubbermaid 18 in. microfibre finish padRubbermaid 18 in. microfibre finish pad900080-800—
17 in. orbital floor machine, 2 speeds17 in. orbital floor machine, 2 speeds402030-17—

The products DMT recommends. The codes can also be ordered with DMT Scan.

A floor machine for the day?

DMT rents a TORNADO 19 in. floor machine. Call DMT for the price, duration and availability.

Book: 450 670-4236