Floor

Strip a floor

Remove the old layers of finish and start fresh. Here is how to do it, in order, without damaging the floor.

Level: intermediateIdeally 2 peopleFloor closed until it is dry everywhere
FloorsEquipmentStepsMistakesProducts
Before you start: read the stripper's label and safety data sheet. The times and dilutions in this guide are guidelines. The product label is always right. Never mix two chemical products.

1On which floors?

Yes

Vinyl tiles (VCT), commercial vinyl, most resilient floors with an acrylic finish.

No, or not without asking

Wood, marble and natural stone, natural linoleum, factory “no-wax” floors, rubber. The wrong stripper can stain or dull them for good. Call us first.

2The equipment

ItemWhy
Floor stripper or low-speed floor polisher (about 175 revolutions per minute)To scrub in the stripper. DMT rents one (see below).
Black pad (stripping)The most aggressive pad, made to remove finish.
Dual bucket with wringer, stripper mopTo spread the stripper. Keep one mop just for this.
Wet vacuum, or squeegee and dustpanTo pick up the stripping “slurry.”
Scraper and hand padThe corners and the edge of the baseboards, where the machine can't go.
Nitrile gloves, safety glasses, non-slip bootsThe stripper is an irritant, and a wet stripped floor is very slippery.
“Slippery Floor” signs, painter's tapeTo close off the area and protect the bottom of walls and frames.

3The steps

  1. Prepare the room

    Move out the furniture and rugs. Sweep or dry-mop: sand under the pad scratches the floor. Put up the signs, and the tape on the bottom of the walls if needed.

  2. Dilute the stripper

    DECAPLUS is diluted in lukewarm water. The more layers of finish there are, the stronger the mixture:

    1 to 8 (111 ml per litre) light buildup, or automatic machine

    1 to 6 (167 ml per litre) medium buildup

  3. Apply in small sections

    Spread a generous amount of stripper, about 10 ft by 10 ft at a time. Wet it well: the stripper only works as long as it is wet.

  4. Let it work

    Don't scrub right away: let the product soften the finish. 3 to 5 minutes

    Never let it dry. If it starts to dry, add a little more.

  5. Scrub with the machine

    Run the floor machine with the black pad, in overlapping lines. Do the corners and edges by hand with the scraper.

  6. Pick up the slurry right away

    Vacuum or squeegee before it dries. Dried slurry sticks back onto the floor and you have to start over.

  7. Rinse with water only

    Rinse well with clear water, with a mop, to remove as much stripper as possible. A clean mop and clean water. Leftover stripper keeps the finish from bonding.

  8. Neutralize with DMT Calcium

    Dilute the DMT Calcium: 1 to 200 (5 ml per litre of water)

    Wear gloves and safety glasses. DMT Calcium is a corrosive acid: it burns the skin and eyes. Always pour the product into the water, never the water into the product.

  9. Check

    Once dry, the floor is matte, with no white marks or shiny patches. Run a fingernail over it: nothing should lift. Otherwise, redo the area.

  10. Let it dry completely

    There is no fixed time: the floor stays closed until it is truly dry everywhere, corners and edges included. It must be completely dry before the sealer or finish. Next: apply the floor finish →

4The costly mistakes

5What you need from DMT

PhotoProductCodeSafety data sheet
Orbital floor stripper-polisher, 17 in, 2-speedOrbital floor stripper-polisher, 17 in, 2-speed402030-17—
17 in black HIPRO pad, 3M 730017 in black HIPRO pad, 3M 7300920017-HP—
Doodle Bug swivel pad holder, 4 x 9 in910050—
Black utility pad, heavy-dutyBlack utility pad, heavy-duty910083-N—
48 in floor scraper, 4 in blade48 in floor scraper, 4 in blade700230-448—
DECAPLUS floor stripper, Unica, 4 LDECAPLUS floor stripper, Unica, 4 L502033-1Coming soon
SPRAYWAY baseboard stripper, 19 oz (edges)502039-1Coming soon
DMT Calcium, calcium remover cleaner, 4 L (neutralize, step 8)DMT Calcium, calcium remover cleaner, 4 L (neutralize, step 8)300102-O1Coming soon
Bucket and wringer 7580J, 33.1 LBucket and wringer 7580J, 33.1 L907580-J—
Fibreglass mop handle, 60 inFibreglass mop handle, 60 in900035-C60—
Wooden handle, threaded tip, 60 inWooden handle, threaded tip, 60 in900031—
White mop, synthetic head, 24 ozWhite mop, synthetic head, 24 oz900003—
Foam floor squeegee, 22 inFoam floor squeegee, 22 in907902-22—
DustpanDustpan900092-497—
Nitrile gloves990013-SP1—
“Wet Floor” sign“Wet Floor” sign906111—
Masking tape, 2 inMasking tape, 2 in600005-2V—

The products DMT recommends. The codes can also be ordered with DMT Scan.

No floor stripper? Rent one from DMT.

Clark 17 in floor stripper, KENT 20 in floor polisher. Call DMT for the price, duration and availability.

Book: 450 670-4236